Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be completed in just a few procedures.

• Begin by ensuring your red dot sight is activated.
• Identify the small reset button on the side of the unit.
• Employ a small object to activate the reset lever for approximately three milliseconds.
• Disengage the switch and your Holosun EPS Carry Red Dot sight will reboot.
• Your red dot sight should now be returned to its factory settings.

Restore Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, determine the tiny button on the bottom of your optic. Then, keep pressed it for around ten seconds until you see the red dot blink. Your Holosun EPS website Carry is now returned to its factory settings, ready for accurate shooting.

restore Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Simultaneously press and hold the power button for approximately 7 seconds.
• A message will flash, indicating that the reset is being performed.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and confirm your sight's functionality. If you encounter any further difficulties, don't hesitate to seek help from Holosun's support.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• First, Turn on your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• While continue holding these buttons, tap the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Permit the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reset your Holosun EPS Carry through a Factory Standard Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the fix. This will set back your sight to its initial settings, clearing any custom configurations you've made. To execute this reset, adhere to these straightforward steps:

• To begin, find the reset button on your EPS Carry.
• Secondly, use a fine object, like a toothpick, to push the reset button.
• While keep the reset lever pressed, turn your EPS Carry.
• The sight will flash a message showing that the reset is finished.

Once the reset is successful, your EPS Carry will be set to its factory settings.

Report this wiki page